Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

One-step preparation of the superhydrophobic Al alloy surface with enhanced corrosion and wear resistance

Corrosion and wear failures are bottlenecks for restricting applications and developments of Al-based functional materials. As a new lubrication technology, superhydrophobic preparation provides an effective way to settle Al alloy corrosion. The preparation methods of superhydrophobic Al alloys are mainly multistep strategies. In this study, superhydrophobic Al alloy, has been prepared by an efficient one-step electrochemical etching process. Meanwhile, its micromorphology has been observed by a scanning electron microscope. The wettability has been measured by video optical contact angle meter. The corrosion behavior has been tested by electrochemical workstation, and wear performance has been characterized by friction tester. The results show that the micro-nanoterraced concave–convex structure has been fabricated and an as-prepared surface exhibits excellent superhydrophobic behavior. Further electrochemical and tribological tests show that corrosion resistance and wear resistance have also been significantly improved. This study provides a new method to prepare wear-resistant and corrosion-resistant Al alloy for widening applications of multifunctional Al-based engineering materials.     

On the Catalytic Activity of Sn Monomers and Dimers at Graphene Edges and the Synchronized Edge Dependence of Diffusing Atoms in Sn Dimers

In this study, in situ transmission electron microscopy is performed to study the interaction between single (monomer) and paired (dimer) Sn atoms at graphene edges. The results reveal that a single Sn atom can catalyze both the growth and etching of graphene by the addition and removal of C atoms respectively. Additionally, the frequencies of the energetically favorable configurations of an Sn atom at a graphene edge, calculated using density functional theory calculations, are compared with experimental observations and are found to be in good agreement. The remarkable dynamic processes of binary atoms (dimers) are also investigated and is the first such study to the best of the knowledge. Dimer diffusion along the graphene edges depends on the graphene edge termination. Atom pairs (dimers) involving an armchair configuration tend to diffuse with a synchronized shuffling (step-wise shift) action, while dimer diffusion at zigzag edge terminations show a strong propensity to collapse the dimer with each atom diffusing in opposite directions (monomer formation). Moreover, the data reveals the role of C feedstock availability on the choice a single Sn atom makes in terms of graphene growth or etching. This study advances the understanding single atom catalytic activity at graphene edges.     

隐式低秩稀疏表示的多视角子空间聚类

针对多视角子空间聚类问题,提出基于隐式低秩稀疏表示的多视角子空间聚类算法(LLSMSC).算法构建多个视角共享的隐式结构,挖掘多视角之间的互补性信息.通过对隐式子空间的表示施加低秩约束和稀疏约束,捕获数据的局部结构和稀疏结构,使聚类结果更准确.同时,使用基于增广拉格朗日乘子交替方向最小化算法高效求解优化问题.在6个不同数据集上的实验验证LLSMSC的有效性和优越性.     

Experimental Study on Hybrid Organic Phase Change Materials Used for Solar Energy Storage

The solar energy utilization in built environment has been limited due to its low heat flux, uneven distribution in time and space and temporal difference in day and night. The phase change materials have been used to collect the fluctuant solar energy to form a stable energy source for the terminal equipment of the buildings. In this study, the hybrid organic phase change materials was prepared for the capillary radiant heating system which formed a cascade utilization of solar energy. Firstly, lauric acid and stearic acid were selected as the basic organic phase change materials and the binary equilibrium phase diagram was completed based on the method of step cooling curve according to the experimental tests data. The results showed that the phase transition temperature of the mixed acid at the lowest eutectic point was 31.2℃ and the latent heat value was 264.3 kJ/kg when the mass mixing ratio was 70% for lauric acid and 30% for stearic acid. Secondly, the expanded graphite was used as an additive to enwrap the mixed acid and enhance the heat conductivity. The experimental results showed that when the mass proportion of expanded graphite in the mixed acid was 10%, the mixed acid could be completely enclosed by expanded graphite and the stability of melting and solidification was optimal. Additionally, the phase transition temperature of the hybrid phase change material was 31.5℃ and the latent heat value was 217.4 kJ/kg. The novel hybrid phase change material has a lower eutectic point and a higher latent heat of phase change, so it has a large application space and is quite suitable for the cascade utilization of solar energy with capillary network heating system.     

Study of tritium transport characteristics in a transportable fluoride‐salt‐cooled high‐temperature reactor

Tritium management is one of the most critical issues that limit the development of fluoride‐salt‐cooled high‐temperature reactor (FHR); therefore, it is important to figure out the tritium transport characteristics in FHRs. In this paper, 3 works concerning about tritium in FHR are conducted: first, the tritium transport characteristics in the primary loop of FHRs are introduced, including tritium production and speciation, the absorption and desorption by graphite, dissolution and diffusion in molten salt, and permeation through structural materials. Second, the physical and mathematical models are established for tritium transport characteristic analysis in a transportable FHR (TFHR). The tritium transport characteristic analysis code (TAPAS) for TFHR is developed and benchmarked. The results prove the fidelity and accuracy of TAPAS. Finally, the tritium transport characteristics in the TFHR are analyzed systematically by TAPAS. Three conclusions are obtained: (1) tritium in the primary coolant loop is mainly in the form of T₂; (2) when TFHR operates at steady state, the permeation rate of T₂ can be regarded as a constant (9.03 × 10⁹ Bq ? EFPD^?1 ); and (3) ⁷Li enrichment and redox potential of molten salt have great influence on the tritium distribution. This work might provide contribution to the tritium control in FHRs.     

Standing Surface Acoustic Wave (SSAW)‐Based Fluorescence‐Activated Cell Sorter

Microfluidic fluorescence‐activated cell sorters (μFACS) have attracted considerable interest because of their ability to identify and separate cells in inexpensive and biosafe ways. Here a high‐performance μFACS is presented by integrating a standing surface acoustic wave (SSAW)‐based, 3D cell‐focusing unit, an in‐plane fluorescent detection unit, and an SSAW‐based cell‐deflection unit on a single chip. Without using sheath flow or precise flow rate control, the SSAW‐based cell‐focusing technique can focus cells into a single file at a designated position. The tight focusing of cells enables an in‐plane‐integrated optical detection system to accurately distinguish individual cells of interest. In the acoustic‐based cell‐deflection unit, a focused interdigital transducer design is utilized to deflect cells from the focused stream within a minimized area, resulting in a high‐throughput sorting ability. Each unit is experimentally characterized, respectively, and the integrated SSAW‐based FACS is used to sort mammalian cells (HeLa) at different throughputs. A sorting purity of greater than 90% is achieved at a throughput of 2500 events s^?1. The SSAW‐based FACS is efficient, fast, biosafe, biocompatible and has a small footprint, making it a competitive alternative to more expensive, bulkier traditional FACS.     

Revisiting the Parallel Strategy for DOACROSS Loops

Journal of Computer Science and Technology - DOACROSS loops are significant parts in many important scientific and engineering applications, which are generally exploited pipeline/wave-front...     

Caution to Apply Magnetic Barkhausen Noise Method to Nondestructive Evaluation of Plastic Deformation in Some Ferromagnetic Materials

Magnetic Barkhausen Noise(MBN) method is known as an effective nondestructive evaluation(NDE) method for evaluation of residual stress in ferromagnetic materials. Some studies on the feasibility of the MBN method for NDE of residual strains were also conducted and found applicable. However, these studies are mainly focused on the state of residual strains which were introduced through a one-cycle-loading process. In practice, however, structures may suffer from an unpredictable and complicated loading history, i.e., the final state of plastic strain may be induced by several times of large loads. Whether the loading history has influences on MBN signals or not is of great importance for the practical application of the MBN method. In this paper, several ferromagnetic specimens with the same final state of residual strain but of different loading history were fabricated and inspected by using a MBN testing system. The experimental results reveal that the loading history has a significant influence on the detected MBN signals especially for a residual strain in range less than 1%, which doubts the feasibility to apply the MBN method simply in the practical environment. In addition, micro-observations on the magnetic domain structures of the plastic damaged specimens were also carried out to clarify the influence mechanism of loading history on the MBN signals.